Plumbing Basics: Before Bathtub Installation

Get Started

The publisher is making a number of great pointers on A Step-by-Step Guide to Installing a Bathtub overall in this post followed below.


Installing A Bathtub
Mounting a bathtub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old tub is readily accessible, the job can relocate easily; if you have to open up a wall surface to remove the old tub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the new one. Ensure you have actually qualified on your own for the work and also fit trying it. Instead of hiring a professional to take over a halfway-completed job, it is much better to think about using one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This article will certainly aid you install a new bath tub in your bathroom if you have currently acquired a new bathtub as well as don't require to change the setup of your previous water system pipes.
Your devices and material checklist need to comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Installment


    Firstly, the supporting framework provided with the bathroom should be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
    Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final placement.

    Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be rather problematic due to the restricted accessibility that is frequently the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Before going on to fit the new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Installing the Tub


    Using the two wooden boards under its feet, place the tub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bath tub until the spirit level reviews level.
    To mount taps, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the same for the other tap.
    Switch on the supply of water and also check all joints and also new pipework for leaks as well as tighten them if necessary. Fill the tub and additionally inspect the overflow outlet as well as the regular outlet for leakages.
    Lastly, repair the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the tub needs to wait up until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipelines.
    If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in location in between the faucet and the sink. Secure the faucet in position with the supplier given backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bathtub


    In the location where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface in between the bathroom and the tiling, bring about complications with moisture and feasible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to securing, to enable the movement experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not consider this motion prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    Do you enjoy more info about How to Install a Bathtub? Post feedback down below. We'd be pleased to find out your responses about this blog entry. Hoping to see you back again later on. In case you liked our post kindly remember to share it. Thanks a lot for taking the time to read it.


    Top service? Contact.

    Leave a Reply

    Your email address will not be published. Required fields are marked *